LAMOLTAN®-Systems

LAMOLTAN® – in-situ foam (operational equipment: storage tanks, fermentation tanks, pipework, etc.)

PUR/PIR – in-situ foam

Installation of operational equipment, in-situ foam to AGI Q 138:

Polyurethan (PUR)- In-situ foam for heat and low-temperature insulation in operational equipment; characteristics, manufacturing, implementation of insulation systems

System series: B2 G56

Thermal insulation materials for building services and operational equipment in the industry to DIN EN 14319-1:

DIN EN 14319-1: Thermal insulation materials for building services and operational equipment in the industry – thermal insulation material made of polyurethane (PUR) and polyisocyanurate (PIR) cast foam manufactured at the application site – part 1: Specification for the foam system prior to installation.

LAMOLTAN® - Ortschaum

Fire performance of rigid foams:
B2 (DIN 4102-1) or E (DIN EN 13501-1)

Fire performance of assemblies:
B1 (= flame retardant to DIN 4102-1) according to general appraisal certificate P-SAC 02/IV-32 Third-party monitoring by MFPA Leipzig GmbH (society for materials research and testing institute for the construction industry in Leipzig, Germany)

LAMOLTAN® - Ortschaum

LAMOLTAN® – Spray foam
A seamless and jointless polyurethane thermal insulation can be applied using our 2-component polyurethane spray foam systems. Challenging surface geometries can also be effectively insulated.

PUR spray foam can also be used in the agricultural sector to insulate potato stores or cattle sheds, for example. It can also be used as internal insulation in industrial and residential buildings on basement ceilings and inner and outer roof surfaces.

Our spray foam systems are available with bulk densities from 35 kg/m³ to 500 kg/m³.

The systems for the construction industry are CE certified to EN14315-1.

Our DS5 roof spray foam system is approved by the German Institute for Construction Technology in Berlin.

Thermal insulation materials for construction engineering – thermal insulation material manufactured at the application site from polyurethane (PUR) and polyisocyanurate (PIR) spray foam – part 1: Specification for the foam system prior to installation.

LAMOLTAN® - Spritzschaum

LAMOLTAN® - Spray foam

LAMOLTAN® – rigid foam for insulation of containers (hot water cylinders, heating cabinets, laboratory instruments, etc.)

Tested according to DIN EN 14308:

DIN EN 14308: thermal insulation materials for building services and operational equipment in the industry – products manufactured at the factory from polyurethane rigid foam (PUR) and polyisocyanurate foam (PIR) – specification.

The insulation corresponds to Euroclass E (DIN EN 13501-1) or building materials class B2 (DIN 4102-1)

LAMOLTAN® - Hartschaum

LAMOLTAN® - rigid foam

LAMOLTAN® Fire Coating

Fire Coating – in all situations where a higher level of flame protection is required. Our fire coatings can be used to manufacture flame retardant spray foam insulation.

Fire Coating Typ A
is a protective dispersion-based coating containing halogen-free flame retardant agents.
With Fire Coating Type A, a dark grey coating is applied to the surface of the polyurethane rigid foam. With this coating, spray foam insulation with LAMOLTAN® B2-S7-25-0 vs satisfies the flame retardancy requirements according to EN 13501-1 (B s3 d0).
This is confirmed by the classification report KB 3.1/15-081-2 issued by MFPA Leipzig.

When combined with Fire Coating Type B, a light coloured paint can be applied to the fire protection coating. The flame retardancy in this case has also been confirmed by MFPA Leipzig.
(KB 3.1/15-411-3, classification C s2 d0)

Please contact us if you require more information.

LAMOLTAN® – rigid foam for manufacturing of insulating half shells (pipe insulation, distribution boards, etc.)

Tested according to DIN EN 14308:
DIN EN 14308: thermal insulation materials for building services and operational equipment in the industry – products manufactured at the factory from polyurethane rigid foam (PUR) and polyisocyanurate foam (PIR) – specification.

The insulation satisfies Euroclass E (DIN EN 13501-1) or building materials class B2 (DIN 4102-1)

Working temperature -30 bis +130 °C

Isolierhalbschalen

LAMOLTAN® – rigid foam for manufacturing of
housings, roof structures, sanitary modules, formed parts for ventilation technology, automotive industry, etc.

Our integral rigid foams are generally water-driven, but they can also be used with all approved physical raising agents.

LAMOLTAN® - rigid foam

LAMOLTAN® – rigid foam for manufacturing of
lifeboats / boat hulls / life saving appliances at sea

This system is certified by Lloyd’s Register for use as flotation devices in lifeboats and life jackets.

The system satisfies the requirements of IMO Res. MSC.81(70) , Part 1 as amended by Res. MSC.226(82) and Res. MSC.323(89).

This system is listed by the US Coast Guard.

Lifeboats

LAMOLTAN® – rigid foam for manufacturing of sandwich panels (sectional doors, roof and wall elements, container construction, etc.)

Our corresponding systems are generally water-driven, but they can also be used with all approved physical raising agents.

LACKFA - Sandwich panels